Jump to content

ClassicFlyTying.com Sponsors
Hand Made Salmon Hooks
Ronn Lucas, Sr.
[email protected]


Tying a winged wet fly - The Dark Montreal

  • Please log in to reply
7 replies to this topic



    Advanced Member

  • Members
  • PipPipPip
  • 1,718 posts

Posted 29 November 2013 - 03:44 PM

This is how i tie winged wet flies. Its not the only way to do things, but it sure works well enough for me.


This may or may not be a variant, depending on how strictly you follow the pattern. Regardless, for all intents and purposes, this should give you a good run through how to tie a nice winged wet fly.




Hook: Wet fly hook of choice, in this case, Mustad 3123 Size 7

Tag: Gold mylar, #16

Tail: Claret schlappen fibers

Body: Danville 4 strand floss, Wine

Rib: Same piece of gold mylar used for the tag

Throat: Claret Schlappen Fibers 2-3 bunches

Wing: Dark Mottled Turkey Wing


1.Start with the hook in the vise. Make a 3 or 4 turn jam knot with heavily waxed thread, then

catch in your mylar for the tag. You want a gold tag, so if using double sided mylar, the gold side should be touching the shank and you should see the silver side. Make sure the piece of tinsel is long enough to form the tag and the rib.



2. Take the thread along the shank of the hook, keeping the mylar on the bottom of the shank, and stop the thread at or just slightly past the point of the hook.



3.Make a 5 turn tag (photo is blurry, but you should have touching wraps.



4. Then make another 5 turns back up to the tie in point. In total you should have 10 turns of tinsel. Tie off the tinsel with two turns of waxed thread and then catch the remain tinsel in the material clip on your vise.



5. Take bunch of claret schlappen fibers and measure a tail approximately the length of the hook shank



6. With touching wraps of thread, secure the schappen along the top of the shank to eye of the hook. By doing touching wraps you create a nice smooth underbody for the floss body of the fly.



7. Secure a single strand of wine floss at the eye of the hook, on the bottom of the shank, with 4-5 tight wraps of thread. Wind the floss in touching wraps to the butt of the fly. Make sure the floss is flat, if it becomes twisted, unwind it as you wrap. I wrap by hand, with no bobbin. At this stage, you can secure the floss with your hackle plier and burnish the body (first layer). Then take the floss back up to the eye of the hook, again with tight touching wraps of flat floss



8. When the floss is back at the eye of the hook, unwind the thread wraps (4-5) that you used to secure the the floss. Then take the two tag ends and secure both together with 4-5 wraps.

Wind your rib in even, open spiral to make 5 ribs on the body. Now, unwind again, 2-3 of the wraps of thread you used to secure the floss tags (there should be two wraps still holding the floss, catch in the rib and secure with 2-3 tight wraps of thread. All the wrapping and unwrapping reduced the bulk at the head tie in area and helps provide a level foundation for the wing of the fly.




    Advanced Member

  • Members
  • PipPipPip
  • 1,718 posts

Posted 29 November 2013 - 03:51 PM

9. Take three or 4 bunches of claret schlappen and secure to the underside of the shank to create the throat of the fly. I usually aim for the fiber tips to lie between the point and the barb of the hook. As you can see there is minimal bulk at the wing tie in area. I use 2-3 tight wraps for each bunch of schlappen, always unwinding 1-2 wraps before I secure the next bunch, so with three bunches of schlappen you should have 6 max. wraps holding them all in place.



10. Measure your wing fibers against the gape of the hook. In this case, 17 fibers per size was good for this hook. Measure your wing to end just past the bend of the hook, but not longer than the tail, and secure with 3-4 TIGHT wraps of thread, always moving forward from the intital wrap.

When your happy, your wing should look like this.



11. Hold the wing with your non tying hand (left hand for me) and cut the butts of the wing at the same angle as the eye of the hook. I lie my scissors on the eye and trim the butts.



12. With waxed thread, secure down the butts with just enough wraps to make the head and whip finish the fly.



13. Take your varnish of choice and apply a few coats to finish the fly with a nice shiny head.

I used cellire for this fly, but sometimes I use Sally Hansens Hard as Nails.



The finished article.



#3 Charlie Vestal

Charlie Vestal

    Lakewood, Colorado

  • Members
  • PipPipPip
  • 1,405 posts

Posted 29 November 2013 - 04:54 PM

Most excellent.

Chemical Engineering: Solving problems you didn't know you had, in ways you don't understand ......

#4 feathers5


    Advanced Member

  • Members
  • PipPipPip
  • 295 posts

Posted 29 November 2013 - 05:45 PM

Very nice. Thanks for the SBS. It really is a help to me as a beginner.

#5 flyryan


    Ryan Houston

  • Members
  • PipPipPip
  • 5,480 posts

Posted 29 November 2013 - 06:21 PM

lovely sbs

Ryan Houston


to see the rest of the flies i have tied just visit  facebook page and browse my photos or galleries






#6 geraldsherbrook


    Advanced Member

  • Members
  • PipPipPip
  • 19,617 posts

Posted 29 November 2013 - 08:10 PM



I agree FULLY with everyone else !!! BRAVO my friend for bringing this 'realy nice and to the point' tutorial of this ('Bergman') classic !


Every thing works for me !!! YOU did and show !!!


I am sure it will be of great help for a whole whole lot of our members...present and future ones !



Voted Sexiest Fly Tyer for 2013

#7 Marc LeBlanc

Marc LeBlanc

    Advanced Member

  • Members
  • PipPipPip
  • 1,888 posts

Posted 29 November 2013 - 10:29 PM

Great job Eunan. 



#8 jockeyb6


    Advanced Member

  • Members
  • PipPipPip
  • 186 posts

Posted 30 November 2013 - 03:16 AM

Excellent photos and write-up!